You can configure this router to us a VPN all the time

Is this the router everyone uses to convert gen 2 Starlink for rv installation?

LCS in Valencia, they have an English speaking lawyer

Thanks!

[удалено]

According to them this is not an issue and I should pay if I want it fixed. Anyway, as others pointed out, this might not be such a big deal because the VIN can be found in some other places. I think I panicked little too quickly

Of course you should spend your own money to fix what they shop messed up. That sounds perfectly normal to you...?

It was an emergency repair while I was traveling. But even if I go back, they want me to pay for the repair because this is not an issue according to them

Orrrrrr...

Please, go on…

I’d go with A1. I have Prusa Mini, same surface as A1 mini and I found there are bunch of stuff I was not able to print because of the size of the model. So yeah, I’d go for the larger build plate

What are some of these prints you wanted to print? I usually don’t know what I want until I want it.

Same here, I don’t plan prints months ahead. For example - the hydroponic system I printed recently can fit on the larger bed only. Starlink gen 2 dish enclosure, the bottom enclosure for Prusa Mini can be printed on a larger bed only, which is funny. Mitotuyo caliper box can be printed on a larger bed only.

Most likely it will not.

Thanks

So im doing mine now, How did it goo 4Y. ;-)

I printed the same one that you have on the photo, but from PLA. It will be indoors. I still need a bucket from Ikea tho

Awesome. Have you got any links to your plans or stl?

You can find them anywhere. Search “hydroponic tower” thingiverse or printables and you’ll get bunch of of results.

Changing the WIPRO RX levels for the TX does not impact the onboard recordings on the TX. It only affects the RX.

Thanks!

I watched few YouTube videos addressing this issue, and it seems to be a hardware problem with Dji Mic 2. The only fix I found so far was not plugging it in but doing onboard recording and then syncing the audio

I don’t know the answer to your question but I get the same results with Bambu ABS. I’ll just bookmark the thread and hope someone has the right answer

You should print them and upload a photo of the print, otherwise your model might get removed from makerworld. Bunch of people got their models removed for posting only renders and no photo of the actual print

Those are usually used for soldering electronics like raspberry pi zero, esp32 etc. maybe jewelry making as well. They’re not very strong but useful sometimes. I printed two without the desk clamp and they are great help when I’m soldering. What I mentioned is not the only use case, of course but get what I mean and how strong they are

It does not change back to 24bit until you change it back. I use the set as stand alone 32bit audio recorders without the receiver and have no problems.

Awesome, thanks!

Struggled for 2 weeks to print large ribbed parts using elegoo ASA without lifting & warping on P1S. Had to drastically tweak flow & speed parameters from generic profile.

Thanks! I’ve never had any issues with warping or adhesion. With either Bambu or eSun filaments but I’ll try what you suggested and see if it works for me as well

I've printed a couple rolls of Bambu Olive ABS and they turned out great. Also printed a roll of 6yr old hatchbox orange and it too was great.

Thanks! Yes, looks like a lot of people use custom settings for the ABS filament. The PETG and 2 of the ABS rolls fixed themselves somehow and I got decent results. Only the white Bambu ABS filament still refuses to print properly. But I’ll try and use custom settings and see if it works

Silica is for pulling moisture out of the air not for drying fillament,

I never said I’d dry the filament with it. That’s why I mentioned “to keep the filament dry”. Here is a photo of what I meant:

it works but you'll have to measure the humidity or just dry it on a schedule. compared to the color change silica you can get that lets you know it needs dried by turning pink

Thanks! I was referring to this setup

I can get you on the app

What’s required to get this done?

You probably won’t find many users unless they’re Chinese. I tried 3 times getting an invitation to register and still couldn’t find someone to get me on the app. It’s really controlled so I doubt you’ll find many users. I might be wrong tho

stores in Europe selling trailer hitch receiver for 2011 Chrysler T & C?

Thanks! I found one which may or may not fit. They have no idea, so I’ll just have to buy it and see if it works.

You’re supposed to use it for 3d printing, and not for growing weird tomatoes, but ok

It's called knurling. There are plenty of tutorials on youtube.

Thanks! I had no idea it’s called that. I guess that’s why couldn’t find tutorials on YT. Thanks again!